S-GA44 FUEL DISPENSER

S-GA44 FUEL DISPENSER

Pump Type :Optional

Inlet Pressure :>=54kPa.

Flow rate (L/min.) :55±5

Suction Distance (m) :6(verticalmente) / 50(orizzontalmente)

FlowMeter Type : Optional

Accuracy :±0.2%

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter): Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display :Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose: 4.5m

Weight :330kg.

Dimension(L×W×H) : 1270*560*2200(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 26

on and noise of pump, finding whether leakage between axis end and pump cover, checking the excessive jump and swing of V wheel that is called belt wheel past, but now defined as V wheel in GBT/10412�002 General V Wheel. Don’t use water and oil with water to debug or cleanse tank in case of the pump and components of fuel dispenser is rust. Meanwhile preventing freeze water affect the normal operation because of low temperature. Regularly inspect and cleanse strainer, especial after installation a pipeline. With the working time get long the waste in pipeline or tank decrease, the period of checking and cleanse should considerably lengthen. But don’t exceed one month. The strength of V wheel should be appropriate because fuel dispenser low strength result in no oil discharge out or inefficiency. High strength, in another case, would increase the axis loan of motor and pump, fasting bearing abrasion of motor, pump and oil seal. Don’t adjust overflow valve to tight in case of increasing pump pressure so as to flux passing overflow valve, and well as noise, vibration and abrasion. Judgment for common failures Firstly, some failure analysis and correct judgment is necessary before maintenance. The principle of first analysis then disassemble, easy first is the basis to judge trouble. The common failure phenomenon of vane pump is that no delivery, inefficient flux, leakage, noise and abnormal vibration. They will be introduced one by one. No delivery or inefficient flux Apart from pump failure other component and pipeline trouble may also result in this phenomenon fuel dispenser . Here only introduce pump failure and inspection method. Exterior inspection: to check motor that maybe don’t work, or rotate in opposite direction, or lose V wheel. Reversal result f fuel dispenser rom wrongly connecting two phase wire in motor or power supply. Adjusting strength of V wheel or changing a new one deal with wheel slip. However, the reason that motor don’t work are several, either electric or mechanical failure. Disconnecting V wheel at first,

error is stored within TR_Error_Code　　October 2005 IFSF - STANDARD FORECOURT PROTOCOL FP31_2.22　　 DISPENSER APPLICATION　　 Page: 43　　 NO-PROGRESS This event occurs when a FP is released and a valid logical nozzle is selected but no　　 volume pulses are registered within a defined period of time (configured by the　　 contents of the data element Max_Time_WO_Prog). The FP moves to the　　 SUSPENDED STARTED state.　　 PCD Comment:　　 fuel dispenser If the proprietary pump protocol doesnt indicate that volume pulses have been　　 generated the PCD will have to ignore this event.　　 Action : The FP state change is send as an unsolicited data array　　 FP_Status_Message .　　 Action : The FP sends an unsolicited data array　　 (FP_Error_Type_Mess) with minor error No_Progress to the　　 CD and the error is stored within TR_Error_Code.　　 TERMINATE_FP The FP is forced to move to the IDLE state.　　 PCD Comment:　　 As most proprietary FP s don t support the concept of terminating a STARTED　　 FP the PCD will fuel dispenser have to manage the state transitions from STARTED to IDLE.　　 This action will involve dealing with the proprietary FP being IDLE but having its　　 no fuel dispenser zzle removed.　　 If a zero transaction is required (dictated by the contents of the data element　　 ZeroTR_Mode ) the transaction with a zero value must be stored in the transaction　?

Gerhard Schröder. But under Angela Merkel s grand coalition, fewer political pigs run around. This is partly because the new government leaks little and backstabs less. That makes even small rows more interesting. The latest one concerns tax breaks for child care. As part of its �5 billion ($30 billion) programme to boost the economy, the government wanted to induce working parents to hire nannies, creating badly needed service jobs and perhaps boosting Germany s low birth rate. Double-income families with children under 14 would set up to �,000 a year of child-care costs against taxes; those with children under six would qualify only if they spent more than �,000 (to avoid the subsidy going simply to pre-school fee fuel dispenser s). It took some time for the plan s logic to sink in. When it did, there was uproar, showing how German politicians are stuck in the past on family matters. The Social Democrats (SPD) found the measure “socially unjust�because it was aimed at richer families. The Christian Social Union (CSU), the Bavarian sister party of the Christian Democrats (CDU), complained that traditional families with one (male) breadwinner were at a disadvantage. For Ursula von der Leyen, the (CDU) minister of family affairs, and famously a mother of seven children, the row is a mixed blessing. It has raised her party s profile in family affairs, but it has also shown how far it and especially the CSU have to go to accept that there is no longer a monolithic view of what makes a family. Traditionalists even mutter that the busy politician must be fuel dispenser a bad mother. The argument has at least raised Ms von der Leyen s own profile, especially among working mothers. Until recently, critics were saying that, if she has two degrees (in fuel dispenser economics and medicine), can look back at four years spent in Silicon Valley and boast such a large brood, it was only because she came from a family rich enough to pay for generous child care. Now the critics have seen her trying to win more help for all work